Reset your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may require to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected performance. Fortunately, resetting your Holosun is a simple process that can be completed in just a few steps.

• First ensuring your red dot sight is powered on.
• Locate the small reinitialize button on the bottom of the unit.
• Use a thin tool to press and hold the reset button for approximately 5 seconds.
• Let go the lever and your Holosun EPS Carry Red Dot sight will reboot.
• The red dot sight should now be returned to its factory settings.

Return to Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to start fresh, resetting it back to standard configuration is a breeze. First, locate the tiny button on the rear of your optic. Then, keep pressed it for around five seconds until you see the red dot blink. Your Holosun EPS Carry is now reset to its factory settings, ready for accurate shooting.

restore Your Holosun EPS Carry Back to Action

Is your beloved Holosun EPS Carry experiencing some issues? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent unexpected activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these easy steps:

• Hold down the power button for approximately 5 seconds.
• A message will flash, indicating that the reset is in progress.
• Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and verify your sight's functionality. If you encounter any further difficulties, don't hesitate to seek help from Holosun's support.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original click here state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Accomplish these steps carefully to ensure a successful factory reset.

• Beginning with, Energize your Holosun EPS Carry by pressing the power button.
• Subsequently, press and hold both the mode button and the up/down adjustment button simultaneously.
• While continue holding these buttons, activate the power button once.
• The display will show a confirmation prompt indicating that the reset process is initiated.
• Enable the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically power off.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Factory Default". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Reinitialize your Holosun EPS Carry through a Factory Default Settings

If your Holosun EPS Carry is acting up, a factory reset might be the fix. This will set back your sight to its initial settings, clearing any altered configurations you've made. To perform this reset, adhere to these easy steps:

• First, identify the reset switch on your EPS Carry.
• Then, press a fine object, like a toothpick, to depress the reset button.
• As you keep the reset button pressed, power on your EPS Carry.
• The sight will blink a message indicating that the reset is finished.

After the reset is finished, your EPS Carry will be returned to its factory settings.

Report this wiki page